-
摘要: 为适应锂离子动力电池行业发展需求，寻求一种高效高质切片方式，本文研究了多种金宝搏188软件怎么用 器的切片质量。通过影像测量仪和扫描电镜（SEM）对比发现，100 ns脉宽调Q型1 064 nm光纤金宝搏188软件怎么用 器切割正极铝箔时毛刺和热影响区（HAZ）约为15 μm和60 μm，切负极铜箔时HAZ约为200 μm；20 ns脉宽的MOPA光纤金宝搏188软件怎么用 器切割铝箔毛刺10 μm，HAZ约为20 μm，切铜箔时HAZ约70 μm；脉宽为10 ps的固体金宝搏188软件怎么用 器切割铝箔毛刺和HAZ分别约为6 μm和10 μm，切铜箔时实现无熔融重凝区；20 ns脉宽的355 nm紫外和532 nm的绿光固体金宝搏188软件怎么用 器切割铝箔HAZ分别为10 μm和17 μm，切铜箔时HAZ则分别为大于70 μm和100 μm。实验结果表明：脉宽越窄，重复频率越高，切割的极片质量越好，ps金宝搏188软件怎么用 器切割的极片精度最高，质量最好，是切割极片最理想金宝搏188软件怎么用 器。而目前，频率高、脉宽相对窄的MOPA光纤金宝搏188软件怎么用 器切割速度最高，切割的正极片完全满足工业要求，更适合极片切割的工业推广。Abstract: In order to meet the demand of lithium-ion battery industry, and to seek a high-efficiency and high-quality cutting method, the cutting quality by various lasers are investigated. Comparing with the image measuring instrument and SEM, it is found that the burr and heat-affected zone(HAZ) of aluminum foil cut by Q-type 1 064 nm fiber laser with 100 ns pulse width are about 15 μm and 60 μm, and the HAZ of negative copper foil is about 200 μm, the burr and HAZ of aluminum foil cut by MOPA fiber laser with 20 ns pulse width are 10 μm and 20 μm, respectively, and the HAZ of copper foil is about 70 μm. The burr and HAZ of aluminum foil cut by 10 picoseconds pulsed solid laser are about 6 μm and 10 μm separately, a zone of no melting and re-condensation is achieved when copper foil is cut. The HAZ of aluminum foil are about 10 μm and 17 μm respectively when they are cut by 355 nm UV and 532 nm green solid lasers with 20 ns pulsed width. However, the HAZ are more than 70 μm and 100 μm when cutting copper foil. The experimental results show that the narrower the pulse width and the higher the repetition frequency, the better the cutting quality of pole piece. The PS laser cuts the pole piece with the highest precision and the best quality, which is the most ideal laser for cutting the pole piece. At present, the MOPA fiber laser with high frequency and relatively narrow pulse width has the highest cutting speed, and the cut positive electrode piece fully meets the industrial requirements, and is more suitable for the industrial promotion of the pole piece cutting.
-
Key words:
- laser cutting /
- lithium-ion power battery /
- positive electrode /
- negative electrode /
- burr /
- heat-affected zone (HAZ)
-
图 2 调Q光纤金宝搏188软件怎么用 器切割极片质量图(平均功率P=100 W, 波长λ=1 065 nm, 脉宽τ＝100 ns, 金宝搏188软件怎么用 重复频率F=100 kHz, 聚焦光斑约为60 μm, 正极切割速度v=1 800 mm/s，负极切割速度v=500 mm/s)
Figure 2. Quality maps of electrode sheet cut by Q-swiched fiber laser(average power P=100 W, wavelength λ=1 065 nm, duration τ＝100 ns, pulse repetition frequency F=100 kHz, focus beam about 60 μm, cutting velocity v=1 800 mm/s for Al-foil and v=500 mm/s for Cu-foil)
图 3 20 ns MOPA金宝搏188软件怎么用 切割的正负极片(波长λ=1 065 nm, 平均功率P=100 W, 最大单脉冲能量E=0.13 mJ, 脉宽τ＝20 ns, 金宝搏188软件怎么用 重复频率F=760 kHz, 聚焦光斑约60 μm)
Figure 3. Electrode sheets cut by 20 ns MOPA laser(wavelength λ=1 065 nm, average power P=100 W, max pulse energy E=0.13 mJ, duration τ＝100 ns, pulse repetition frequency F=760 kHz, focus beam about 60 μm)
图 4 10 ps金宝搏188软件怎么用 切割的正负极片(波长λ=1 064 nm, 平均功率P=9.1 W, 重复频率F=300 kHz，脉冲宽度τ＝10 ps，单脉冲能量＞50 μJ)
Figure 4. Quality maps of electrode sheets by 10 ps solid laser(wavelength λ=1 064 nm, average power P=9.1 W, duration τ＝10 ps, pulse repetition frequency F=300 kHz, Max pulse energy > 50 μJ)
图 5 532 nm和355 nm金宝搏188软件怎么用 切割的极片(532 nm绿光参数：波长532 nm：平均功率P=16 W, 重复频率F=40 kHz，脉冲宽度τ＝20 ns以及355 nm紫外光参数：波长355 nm，平均功率P=8 W, 重复频率F=40 kHz，脉冲宽度τ＝20 ns)
Figure 5. Electrode sheets cut by 532 nm and 355 nm solid lasers(green laser:wavelength λ=532 nm, average power P=16 W, duration τ＝20 ns, pulse repetition frequency F=40 kHz; uv laser: wavelength λ=355 nm, average power P=8 W, duration τ＝20 ns, pulse repetition frequency F=40 kHz)
表 1 各种金宝搏188软件怎么用 器切割正负极片的质量
Table 1. Qualities of positive and negative electrodes cut by different kinds of lasers
金宝搏188软件怎么用 器及相应参数 正极 负极 评价 532 nm皮秒金宝搏188软件怎么用 器@τ=10 ps,
F=300 kHz, P=9.1 W毛刺：6 μm HAZ:10 μm
切速：2 800 mm/s毛刺：无, HAZ:无熔融热影响区
切速：800 mm/s最优 1 064 nm MOPA金宝搏188软件怎么用 器@τ=20 ns,
F=760 kHz, P=100 W毛刺：10 μm HAZ:20 μm
切速：2 800 mm/s以上毛刺：很小HAZ:熔融区60 μm
切速：800 mm/s较优 355 nm固体金宝搏188软件怎么用 器@τ=20 ns,
F=40 kHz, P=8 W毛刺：小HAZ:10 μm
切速：600 mm/s毛刺：较小, HAZ:＞70 μm
切速：400 mm/s一般 1 064 nm调Q光纤金宝搏188软件怎么用 器@τ=100 ns,
F=100 kHz, P=100 W毛刺：15 μm, HAZ: 60 μm
切速：1 800 mm/s毛刺：-, HAZ:200 μm
切速：500 mm/s较差 532 nm固体金宝搏188软件怎么用 器@τ=20 ns,
F=40 kHz, P=16 W毛刺：小HAZ:17 μm
切速：1 000 mm/s毛刺：-, HAZ:100~200
μm切速：600 mm/s较差 
下载: 导出CSV
-
[1] 戴永年, 杨斌, 姚耀春, 等.锂离子电发展状况[J].电池, 2005, 35(6):193-195. http://d.old.wanfangdata.com.cn/Periodical/dc200503013DAI Y N, YANG B, YAO Y CH, et al.. Development status of lit-ion batteries[J]. Battery Bimonthly, 2005, 35(6):193-195.(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/dc200503013 [2] 朱洪波, 李艳华, 郝明明, 等.基于偏振复用技术的半导体金宝搏188软件怎么用 加工光纤耦合模块[J].光学精密工程, 2013, 21(5):1137-1143. http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201305007ZHU B, LI Y H, HAO M M, et al.. Fiber coupled diode laser module for laser processing by polarization multiplexing[J]. Opt. Precision Eng., 2013, 21(5):1137-1143.(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201305007 [3] 刘杰, 杨永强, 苏旭彬, 等.多零件选区金宝搏188软件怎么用 熔化成型效率的优化[J].光学精密工程, 2012, 20(4):699-705. http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201204003LIU J, YANG Y Q, SU X B, et al.. Efficiency optimization of selective laser melting for multi-parts[J]. Opt. Precision Eng., 2012, 20(4):699-705.(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/gxjmgc201204003 [4] KAWATAS, SUN H B, TANAKA T, et al.. Finer features for functional micro devices-micromachines can be created with higher resolution using two-photo absorption[J]. Nature, 2001, 412(6848):697-698. doi: 10.1038/35089130 [5] LEE D, PATWA R, HERFURTH H, et al.. High speed remote laser cutting of electrodes for lithium-ion batteries:anode[J]. Journal of Power Sources, 2013, 240:368-380. doi: 10.1016/j.jpowsour.2012.10.096 [6] 刘峰, 王立君, 王玉恒, 等.金属材料表面金宝搏188软件怎么用 耦合系数的反演[J].光学精密工程, 2011, 19(2):421-428. http://d.old.wanfangdata.com.cn/Conference/7426813LIU F, WANG L J, WANG Y H, et al.. Inversion for laser coupling coefficient on metal material surfaces[J]. Opt. Precision Eng., 2011, 19(2):421-428.(in Chinese) http://d.old.wanfangdata.com.cn/Conference/7426813 [7] 金国藩, 李景镇.金宝搏188软件怎么用 测量学[M].北京:科学出版社, 1998.JIN G F, LI J ZH. Laser Metrology[M]. Beijing:Science Press, 1998.(in Chinese) [8] 陆建, 倪晓武, 贺安之.金宝搏188软件怎么用 与材料相互作用物理学[M].北京:机械工业出版社, 1996.LU J, NI X W, HE A ZH. Physics of Interaction Between Laser and Materials[M]. Beijing:Mechanical Industry Press, 1996.(in Chinese) [9] LUTEY AHA, FORTUNATO A, ASCARI, et al.. Laser cutting of lithium iron phosphate battery electrodes:characterization of process efficiency and quality[J]. Optics & Laser Technology, 2015, 65:164-174. http://www.sciencedirect.com/science/article/pii/S0030399214002035 [10] 金国藩, 李景镇.金宝搏188软件怎么用 测量学[M].北京:科学出版社, 1998.JIN G F, LI J ZH. Laser Metrology[M]. Beijing:Science Press, 1998.(in Chinese) [11] 浦诺威, 张冬云.金宝搏188软件怎么用 制造工艺:基础、展望和创新应用实例[M].北京:清华大学出版社, 2008.POPRAWE R, ZHANG D Y. Lasertechnik Fur Die Fertigung[M]. Beijing:Tsinghua University Press, 2008.(in Chinese) [12] 陈家璧, 彭润玲.金宝搏188软件怎么用 原理及应用[M].北京:电子工业出版社, 2013.CHEN J B, PENG R L. Principle and Application of Laser[M]. Beijing:Electronic Industry Press, 2013.(in Chinese) [13] 季凌飞, 凌晨, 李秋瑞, 等.皮秒金宝搏188软件怎么用 工程应用研究现状与发展分析[J].机械工程学报, 2014, 50(5):115-126. http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201405016JI L F, LING CH, LI Q R, et al.. Research progress and development of industrial application of pico second laser processing[J]. Journal of Mechanical Engineering, 2014, 50(5):115-126.(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201405016 [14] 陈发良, 李东海.基于Fokker-Planck方程的电介质材料短脉冲金宝搏188软件怎么用 破坏机制分析[J].强金宝搏188软件怎么用 和粒子束, 2011, 23(2):334-338. http://d.old.wanfangdata.com.cn/Periodical/qjgylzs201102011CHEN F L, LI D H. Mechanism of short-pulse laser induced damage in dielectric based on Fokker-Planck equation[J]. High Power Laser and Particle Beams, 2011, 23(2):334-338. (in Chinese) http://d.old.wanfangdata.com.cn/Periodical/qjgylzs201102011 [15] 顾理, 孙会来, 于楷, 等.飞秒金宝搏188软件怎么用 微加工的研究进展[J].金宝搏188软件怎么用 与红外, 2013, 43(1):14-18. doi: 10.3969/j.issn.1001-5078.2013.01.003GU L, SUN H L, YU K, et al..Research progress of micro-nanofabrication by femtosecond laser[J]. Laser & Infrared, 2013, 43(1):14-18.(in Chinese) doi: 10.3969/j.issn.1001-5078.2013.01.003 [16] HÜTTNER B, ROHR G. On the theory of ps and sub-ps laser pulse interaction with metals:Ⅰ.surface temperature[J]. Applied Surface Science, 1996, 103(3):269-274 doi: 10.1016/0169-4332(96)00523-5 [17] 何飞, 程亚.飞秒金宝搏188软件怎么用 微加工:金宝搏188软件怎么用 精密加工领域的新前沿[J].中国金宝搏188软件怎么用 , 2007, 34(5):595-622. doi: 10.3321/j.issn:0258-7025.2007.05.001HE F, CHENG Y. Femtosecond laser micromachining:frontier in laser precision micromachining[J]. Chinese Journal of Laser, 2007, 34(5):595-622.(in Chinese) doi: 10.3321/j.issn:0258-7025.2007.05.001 -
下载:
计量
- 文章访问数: 4592
- HTML全文浏览量: 2870
- PDF下载量: 513
- 被引次数: 0
